#TRADESKILLMASTER 3 GUIDE ISO#
≤5mA, 1min, No breakdown, no flashover, basic insulation Input to Earth 2120 Vdc 2 Insulation resistance Input to Output ≥50 MΩ Test Voltage 500Vdc Input to Earth ≥50 MΩ 3 EMI RE GB / T 18655-2010,Ĭhapter 6.4, CLASS 3 standard – CE 4 EMS Radiation Immunity GB/T 6113.1 – High Current Injection ISO 11452-4: 2005Īrticle 7, 100mA RF Immunity ISO 11452-9 Conducted Immunity ISO 7637-2: 2004 Articleĥ Transient Conducted Immunity ISO 7637-3: 2007 Articleģ.4.2 Electrostatic Discharge ISO 10650-2008 Structure and Interface Description Safety Regulations and EMC Characteristics Item Parameter Value Unit Remarks 1 Withstand voltage Input to Output 2120 Vdc Leakage current Enable hard-wired control for DCDC sleep and wake up, high level wake up. Enable hard-line control of DCDC converter on / off, high level start Ģ. Logical function If the customer has no special logic requirements, the default is:ġ. Support hard-wired and arbitrarily formulated message sleep and wake-up. Can report DC-DC working status, input voltage, output voltage, output current, hardware failure, communication failure and other information ģ.
#TRADESKILLMASTER 3 GUIDE SOFTWARE#
With BootLoader function, software can be updated by CAN communication Ģ. Secondary) ℃ If all met, work properly 10 CAN communication function 1. Voltage Protection Recovery 95(Primary)/90( Recovery 8 Input Reverse Connection Protection DC-DC input does not start after reverseĬonnection – 9 Overheat Protection Power attenuation 100(Primary)/112( Secondary) ℃ When the temperature reaches the attenuation point, the module limits the power output the power is attenuated at 8% / ℃ Limit mode 7 Output Short Circuit Protection – Instant protection, automatic Recovery point, works normally 6 Output Current Limit Protection 130☒ A When the output current increases to the current limit protection point, it enters the constant current voltage Output Recovery point 15.5☐.5 Vdc If less than Recovery 5 Output Overvoltage Protection Protection point 16.0☐.5 Vdc If greater than protection point, turn off Recovery Recovery point 9.0☑ Vdc Instant protection, automatic Recovery 4 Output Undervoltage Protection Protection point 7.0☑ Vdc Instant protection, automatic
Input and Output Characteristics Item Parameter Value Unit Remarks 1 Input Voltage range 280-450 Vdc 200~450 2 Input Current 6.8 A 3 Input Inrush Current 8.2 A Capacitance spikes inĠ.5 ms not Counted 4 Input current in standby 5A 7 Voltage Reporting Error <0.2 V 8 Current Control Error <1 A Control Precision 9 Voltage Control Accuracy <0.2 V 10 Work Efficiency >94.5 % 40%~70% Load Non-CAN operation is accomplished by connecting as shown in the diagram below Environmental Conditions Item Parameter Value Unit Remarks 1 Working Temperature -40 to +85 ℃ 2 Ambient Storage Temperature -40 to +105 ℃ 3 Relative Humidity 5 – 95 % Non-condensing 4 Cooling Method Air-cooled – Outside the Shell 5 Protection Class IP67 – Shell Part 6 Working Noise <60 dBA Air Cooling System 7 Anti-vibration Leve GB 413-2002 3.12 – Requirements for Non- engine Parts Electrical Performance.Includes optional CAN communication, BootLoader function, low voltage enable control, high voltage sleep and designated CAN message sleep function.High peak power and strong overload capacity, meeting the usage requirements of impact loads.Utilizes dual controller digital architecture, with automatic protection and fault diagnosis functions.
Input and output are completely electrically isolated, safe and reliable.